车库门日常维修保养及常见问题处理方法

Garage door daily maintenance and common problems handling methods

车库门日常维修保养：

Garage door daily maintenance:

A 手动开门，门若运行不灵活或不平衡，请专业维修人员进行调整。

A manually open the door, if the door is not flexible or unbalanced, please adjust the professional maintenance personnel.

B 检查门是否全开和关严，若不能则调整行程限位开门或调整负载力旋钮。

B check whether the door is fully open and closed. If not, adjust the travel limit to open the door or adjust the load knob.

C 重新做好安全反应测试，做必要调整。请维修人员检查线缆，门体平衡弹簧及其它硬件。

C completes the safety response test and makes necessary adjustments. Ask maintenance personnel to check cable, door balance spring and other hardware.

车库门常见故障及处理方法：

Common faults and handling methods of garage doors:

1.用手动开关或遥控器不能启动驱动装置

1. do not start the drive with manual switch or remote control.

驱动装置没有接通电源

The driving device is not connected to the power supply.

手动开关或遥控接收板断路

Manual switch or remote control receiver circuit breaker

运行次数过多导致电机热保护

Excessive operation time leads to motor thermal protection.

检查插座、插头、手动开关、保险管熔丝

Check socket, plug, manual switch, fuse fuse.

检查手动开关及遥控接收板接线

Check manual switch and remote receiving board wiring.

重新定位行程开关以增加行程

Reposition the stroke switch to increase the stroke.

2.门关不严或开不完全

2. door is not strict or not fully open.

行程开关位置调节不正确

Incorrect adjustment of stroke switch position

重新定位行程开关以增加行程

Reposition the stroke switch to increase the stroke.

3.手动开关能控制驱动装置而遥控器不能 ·

3. the manual switch can control the driving device while the remote control can not.

遥控器未对码

No code for remote control

遥控系统故障

Remote control system failure

按照说明书指导完成对码操作

Follow the instructions to complete the code operation.

更换遥控器内部电池

Replace internal battery of remote controller

请维修人员检查接收控制板

Please check the receiving control panel by maintenance personnel.

4.门未关紧就自动反向运行或开门时未接触行程开关就中途停止运行

When the 4. doors are not closed, the automatic reverse operation or the untouched travel switch will stop running halfway.

开关门阻力大于设置启闭负载力激活了障碍感应系统

The resistance of the switch door is larger than that of the opening and closing load force, thus activating the obstacle induction system.

连杆长度调节不当

Improper adjustment of connecting rod length

拉开离合装置，检验门体与扭簧是否平衡、启闭是否灵活

The clutch device is opened to check whether the door body is in balance with the torsion spring, and whether the opening and closing is flexible.

增大开闭负载力

Increasing opening and closing load

在门关闭时调节连杆长度

Adjust the length of connecting rod when the door is closed.

5.门体单向运行行程开关损坏或行程开关线短路

5. door one-way running trip switch damage or travel switch line short circuit.

光电开关光路上有障碍物 启闭负载力调节没有到位

The photoelectric switch has obstacles on the optical path. The load regulation is not in place.

检查行程开关及行程开关接线

Check trip switch and trip switch wiring.

清除光电形状光路上的障碍物

Remove obstacles on optoelectronic form.

重新调节启闭负载力

Re adjust load and force on opening and closing

6.门体冲过行程开关

6. door overshoot switch

行程开关损坏或行程开关线断路

The trip switch is damaged or the trip switch line is broken.

检查行程开关及行程开关接线

Check trip switch and trip switch wiring.

7.车库外遥控器作用距离明显低于10米

7. outside the garage remote control distance is obviously lower than 10 meters.

车库屏蔽严重

Garage shielding serious

电池电力不足

Battery power shortage

将天线延长至车库外部

Extend the antenna to the outside of the garage.

将天线伸出驱动器外部并拉直

Extend the antenna out of the driver and straighten it.

更换电池

Replace the battery

8.门体运行噪音过大

8. door operation noise is too large.

五金件安装不牢固

Hardware installation is not solid.

驱动装置拉杆没有位于门体中心线上

The drive rod is not located on the center line of the door body.

门体运行导轨不平行

Non parallel running guide of door body

合页、滚轮处没有涂覆润滑油

There is no lubricating oil on the hinge and roller.

坚固五金件

Solid hardware

调节驱动装置拉杆与门体中心线重合

Adjusting drive device pull rod coincide with center line of door body.

调节门体运行导轨相互平行

Adjust the operation of the door body parallel to the guide rail.

在合页、滚轮处覆润滑油

Grease the hinge and roller.

9.驱动装置正常运行，但门体不运行

9. the driving device is running normally, but the door body is not running.

滑架上的离合器没有复位

The clutch on the carriage does not reset.

启闭负载力调节没有到位

Opening and closing load regulation is not in place.

复位离合器

Reset clutch

重新调节启闭负载力

Re adjust load and force on opening and closing